Showing results: 4186 - 4200 of 5217 items found.
-
PCE Instruments
An automotive tester can be used to inspect one or more aspects of an automobile. For example, a borescope automotive tester is an automotive inspection camera used by auto body mechanics to see inside car, truck and other vehicle engines before removing any engine parts. Other kinds of automotive tester devices are used to adjust belt tension, test the electronic ignition starter, search for air conditioning leaks, measure the force required to press a brake pedal, determine the antifreeze concentration, or check the paint thickness over collision repairs.PCE Instruments (PCE) offers a wide variety of automotive tester products. These diagnostic support tools help professional automobile mechanics identify a number of vehicle repair needs. PCE's automotive tester products can aid in the diagnosis of many different mechanical and electrical system issues, including but not limited to locating the cause of an engine misfire, testing fuel injector resistance, pinpointing an engine coolant leak, or detecting car cylinder head problems. It's no wonder so many auto repair technicians choose to stock theirs shops and garages with PCE automotive tester products.
-
AIM GmbH
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
NRM-2 -
National RF, Inc
National RF’s Resonance Dip Meter is a test instrument used to determine the resonant frequency of a tuned circuit or resonant network, such as an antenna system. In addition, the unit may function as an RF detector, or a secondary frequency source. The instrument is analogous to the older vacuum tube “grid dip meter,” once popular in every electronic laboratory or radio station. Unique to this updated version is a buffered output that may drive a digital frequency counter for exact measurement of resonant frequency, or connected to an oscilloscope to be used as an RF detector and waveform/modulation monitor.
-
NI
The PXI Automotive Ethernet Interface Module communicates with Automotive Ethernet so that you can use the NI‑XNET driver or standard networking drivers to develop applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It provides up to four independent endpoints or up to two network terminal access points (TAPs). With onboard hardware timestamping and the ability to act as 802.1AS masters or slaves, the PXI Automotive Ethernet Interface Module can synchronize with an external network as well as the rest of a PXI system.
-
Pickering Interfaces Ltd.
Fixed power supply modules provide you with up to four separate voltage outputs isolated from the PXI backplane. Any combination of 3.3V, 5V, 12V or 15V can be specified with a maximum current capability of 4A for the 3.3V option; the software provides on/off control and status monitoring for each output. Dual programmable power supplies are capable of supplying up to 60 Watts of power. These are ideal solution for applications where a self contained test system with a high power supply power capability is required in a PXI format.
-
T10 -
SONOTEC GmbH
The T10 structure-borne sound probe can be used to monitor the condition of machines, systems and processes, provided that they generate detectable structure-borne sound in the ultrasonic range. Changes in the sound signals indicate a change in the condition and/or process of the plant. The detection of these changes forms the basis for condition monitoring in preventive maintenance. The T10 structure-borne sound probe is used when the installation space is very limited or the test specimen must not be loaded with a large sensor mass. The T10 structure-borne sound probe is also suitable for use on non-magnetic surfaces.
-
CommFront Communications
Most data networks are complicated, not just the hardware and network issues, but also the high-level protocols that devices use to communicate; and to make things even more complicated, many manufacturers have incorporated proprietary protocols for their devices. Integrating different devices and protocols within a data network is always the most challenging task for system integrators, firmware / software developers, and site engineers. From the simplest loopback test to complicated checksum calculation and sophisticated firmware and GUI software development, the 232Analyzer is designed to tackle all these challenges.
-
TF225 -
TESTEX Testing Equipment Systems Ltd.
Circular Locus Tester, to determine surface deterioration and quality of fabrics (wool, chemical fiber, mixed, kitted and woven fabrics). Using an active friction system, fabric is rubbed against a nylon brush and abrasive or an abrasive only under controlled conditions. Results of the test are achieved in minutes. The relative motion of the locus specimen grip and the abrasive platform is a circle with a relative speed of 60+/-1 r/min. The grip offers pressure to the specimen which is adjustable with a tolerance of +/-1%. For added control and safety, the machine is equipped with a self-stop switch.
-
8000 -
Photon Kinetics
The 8000 OTDR is the first of a new generation of OTDRs that has been designed specifically for optical fiber and cable test applications. Its revolutionary "performance first" optical design delivers unsurpassed optical performance, and its MS Windows operating system facilitates integration of the OTDR into manufacturing networks. These features, combined with unique data acquisition capabilities, significantly reduce the time associated with many aspects of the OTDR measurement process, making it possible for fiber and cable manufacturers to increase production output and reduce manufacturing costs.
-
ADSE 550 -
ATEQ Aviation
The ADSE 550 pitot static tester, housed in a plastic carrying case, is a portable, self contained field tester designed to test aircraft pilot ans static systems for leaks as well as the operation and calibration of airspeed, altimeter, engine pressure ratio, manifold pressure indicators, and other vacuum or low pressure units. The tester consists of a hand-operated vacuum pump, a hand-operated pressure pump vacuum and pressure gauges, 5 control valves, an altimeter and an airspeed indicator. The package accessories include two 25-foot hoses.
-
ProDAQ 3000 Series -
Bustec Ltd.
The ProDAQ 3000 Series includes interfaces and controllers. ProDAQ VXIbus slot-0 interfaces make the connection from PC to VXIbus mainframe, providing access to VXIbus instruments. Users can build test and measurement systems by connecting instruments via standard computer interfaces to an existing computer. ProDAQ VXIbus slot-0 controllers provide a fully-customizable platform for embedded applications and support 2eVME and 2eSST transfers between controllers and instruments. Users can configure the ProDAQ 3000 Series of Controllers for use as a VXIbus processor module in non-slot-0 applications.
-
CPS2000 -
Boonton Electronics
CPS2000 True Average Connected Power Sensors provide USB, LAN and PoE capabilities to enable easy RF power measurement of modulated and CW signals from 50 MHZ to 8 GHz. Compatible with Windows and Linux systems, CPS2000 sensors include all the necessary drivers for programming through SCPI, IVI and LabVIEW. Connectivity and compatibility, combined with 60 dB dynamic range and 100 measurements per second, CPS2000 sensors are the ideal solution for lab, field, production test, ATE remote monitoring and embedded environments.
-
Advanced Power Designs, Inc.
Advanced Power Designs is the first to introduce programmable DC power supplies on dual C-Size VXI card formats. Designed specifically for easy integration into new VXI automatic test systems, these state-of-the-art power supplies are fully compliant with all VXI specifications for direct installation into any standard C-Size VXI card cage. They can even be purchased with LABVIEW, LABWINDOWS, CVI or HPVEE Graphical User Interfaces*, and a fully integrated command and control software program written for the National Instruments MXI I/O. protocol.
-
Piranha4 -
Teledyne DALSA
The Piranha4 cameras offer advanced features such as sub-pixel spatial correction, areas of interest (up to 4 at a time) to reduce data processing and simplify cabling, as well as dual-line area mode to double line rate, HDR mode, shading and lens correction. The Piranha4 is built for the real world with features to ease system integration. The advanced GenICam compliant user interface makes it easy to set up and control camera parameters such as exposure control, FFC, white balance, gain, test patterns, diagnostics and more.
-
TPS Associates, Inc.
TPSA has over 20 years of experience in Engineering Design & Software Development including:Hardware & Software DesignOTPS Acquisition SupportSystems Installation & SupportAircraft Modification/CertificationEngineering Studies & AnalysesFunctional & Systems TestingIndependent Verification & Validation (IV & V)Test Program Set EngineeringReliability & Maintainability (R&M)Engineering Drawings & DataConfiguration Data ManagementReverse EngineeringRequirements AnalysisSupport Equipment (SE)Aircraft Launch & Recovery Engineering (ALRE)Engineering Change Proposal (ECP) ReviewTechnology Insertion (TI)PDR, CDR, FAT, Techeval, OSV Support
